PS-47 through 59 make excellent industrial vents when modified by adding Styrene Strips to every other slat. They can also be used as window awnings. Styrene (also known as Hi-Impact PolyStyrene) is the most commonly used plastic in molded plastic kits (Model Railroad, Automobile, Airplane and Ship). For that reason, we have chosen Styrene as the medium in our New FineLine Structural model parts for compatibility in kit-bashing. It may be combined with wood, metal and other plastics using special glues or cements. Styrene has a tendency to be brittle, especially after lengthy U.V. exposure or painting. It is easily warped by solvents, so care must be taken when cementing flat sheets for walls, and reinforcement bracing is recommended. When constructing closed tanks or structures, venting is recommended to allow the inside and outside temperatures to equalize. Styrene has excellent forming characteristics and bonds rapidly and permanently. Styrene plastic cuts easily using the “scribe and break” method. Only use Enamel, Alkyd Oil, Latex or Acrylic paints specified for Styrene plastics. ACRYLIC If goods are returned as faulty, generally we will provide a replacement. If the item is of a ‘ready to go’ type model eg.

For fast, clean, accurate cutting of Styrene Shapes, Tubing, Strip and Rod, simply scribe with a hobby knife and snap. When cutting Sheet Styrene, make all scribes first and then bend downward one side at a time until it snaps clean. ABS has been hailed by professional modelmakers as “the best all-around construction material since wood”. Stronger and more rigid than many metals; easier and more flexible to work with than any previous plastic; cleaner and more durable than wood, ABS structural shapes by PLASTRUCT have been used for engineering design models on an international scale since their introduction. ABS is also one of the best plastics for heat or vacuum forming and, of course, has excellent bonding characteristics, not only to itself but to other commonly used plastics.ABS hand rails and stair rails may be curved to fit circular applications by softening them in warm water or heating with a hair dryer. Stairs may be modified to fit the circumference of a tank or other curved surface by cutting off the stair stringer from the side to be cemented. Tape the stair in place. Attach each stair step separately. recommend that goods are returned by recorded or insured delivery. If you would like to phone our despatch department Cobra Motor Paints – Why do you need Cobra Motor Paints? Cobra Motor Paints is a range of acrylic non-toxic colours, perfect for painting any area of the vehicle’s body, rims, tires, engines and interiors. They can be easily applied with both brush and airbrush, and have Don’t miss this special pricing on outstanding covering power while providing a very smooth and uniform matt finish. To provide the distinctive gloss of the bodywork, we have created a special lacquer formula with the accompanying catalyst and thinner. Cobra Motor lacquer offers the same glossy finish as your favourite vehicles. What are the advantages of the Cobra Motor range? • 1 hour drying time • 24-hour curing time • Easy application via brush and airbrush • Odourless • Acrylic and non-toxic • 30ml clear glass bottle • Wide colour range with 62 colours ready to apply to the model.

You have many options when it comes to Plastic Welding and Assembly. The Emabond Process offers certain unique advantages when compared to alternative forms of assembly such as: To create realistic welded (or riveted) tank seams, use a radiator hose clamp as your horizontal guide. Tighten the clamp around the tube, and using a hobby knife, lightly scribe lines every 8 scale feet around the tank. Scribe vertical lines using a straight edge.Professional model makers have used plastics as virtually their sole working material for the past 30 years. However, hobbyists, miniaturists and amateur model builders have, for the most part, continued to use wood, card and brass for their models. There are, of course, applications where those materials are suitable or desirable. But in most cases, Plastruct should be your material of choice.

For the various materials found in PLASTRUCT’s Catalog, the following cements are recommended: STYRENE Copolyester (also known as P.E.T.G.) is tougher and less prone to split or shatter than Acrylic. It has excellent clarity in sheet form, and is resistant to stress whitening. It is easily formable and not prone to warp. Copolyester is quite stable and bonds well to itself, however with most other plastics, a special industrial grade Cyanoacrylate Glue is recommended. Accepts most paints, including lacquer. Cement Guide Diecast – Explore Our Range of Diecast Models At Scale Model Shop, we supply a wide range of diecast models, specialising in aircraft, cars, and tanks. Diecast models are a miniature replica made using a die casting or metal casting method. They are usually made of zinc or lead alloy and come fully formed in a single piece which portrays the vehicle in a smaller scale. Diecast models are much more than a simple toy, they demonstrate a higher level of quality than other plastic kits, due to the higher shelf life. This is great for any enthusiast collector as you can display for years and pass it down to the next generation. It doesn’t matter if you’re just starting out or have been collecting for years, there is no denying how appealing a diecast model collection is. Browse through our range of brands available, including Corgi, Diecast Masters, and Greenlight – there is plenty to choose from! Paint the foam a color that will be a suitable undercoat for your finished landscape. Use latex or acrylic paint. OR, see our Polyterrain or Magic Earth materials.Fittings can be more readily attached to Tubing, particularly in sizes 5/16″ and over, if the pipe is screwed onto the Fitting. Always rotate the Tubing in the same direction whether attaching or removing the Fitting. STYRENE We are pleased to provide the following collection of creative tips for working with PLASTRUCT Plastic Model Parts. Plastruct Model Parts and Accessories are manufactured in several plastic materials. The choice of material was based upon the final use of the Product as well as workability and price. Glue the levels of foam together with the appropriate glue (see our cement guide) and hold in position with nails until the glue dries (allow at least 24 hours). Consider nail placement so they will not affect contour shaping later. For best results in landscaping, plant in groups and use different heights of trees to represent varying ages of the trees as well as for creating depth of field. As you move further from the viewing point or higher in the mountains, use shorter trees. Shorter trees may also be used for potted or tubbed trees.

Exceeds the most demanding specifications for temperature, leak-proof (Hermetic) and pressure requirements You have the right to cancel within 7 working days after the day you take receipt of goods. You must notify us within Basic construction of building shells is usually of a rigid material such as Acrylic, Styrene, Foamboard or plywood. Plastruct Plastic Patterned Sheets can then be applied to create realistic simulated finishes. The material used in our Traditional Round Tubing medium is Butyrate plastic. It has proven to be ideal because it is so convenient to work with. It can be cut, turned, drilled, painted and easily cemented. The Tubing and Tubing Fittings are manufactured to provide a good friction fit and maintain the outside diameter; splines on the male Fittings accomplish tight fit and prevent undesired rotation and still allow intentional turning. This feature permits cementing to be a final operation. The telescoping sizes of the pipe combined with the workability makes improvisation quite simple. PS-25, 26 and 27 make excellent road and highway guardrails when cut into strips and mounted on square posts.

Mailing List

For PPE, you'll for sure need gloves made of neoprene rubber rather than surgical latex types. It will remove the oils in your skin. And definately goggles for the eyes. Had some spalsh in my right eye one time while working on a plane, and it will make a grown man cry!! lol Ventilation is also a must - got 'happy and giggly' due to it one time with my supervisor one time cleaning another fuel tank where ventilation was an issue.