No Neutral Wire Required, SONOFF ZBMINIL2 Zigbee Smart Light Switch (2 Way), Works with Alexa, SmartThings Hub, Google Home&SONOFF ZBBridge-P, ZigBee Hub Required- A Certified for Humans Device

Product Information

A maintenance guy at work recommended having the Lin come from the switch (maybe even embedding this at the fan box rather than the switch box). That way, you can easily hit the switch off if something happens with the zbmini, or even if the mini needs a reset, rather than having to go to the breaker.

Lastly, the ZigBee IC inside is CC2652 which is also present inside the Sonoff ZigBee dongle, which suggests that Sonoff ZBMINI-L will make for a fantastic router in your mesh . (apparently, power requirements in standby mode may prevent Sonoff ZBMINI-L from acting as a router, according to this conversation) There are no dev pads present, but that’s ok. I see no reason to flash these since they work with everything else as is.” The tip is that might be a idea to try unofficial PTVO firmware but select the CC2652R chip type (and not CC2652P) in the PTVO firmware configurator to get firmware image without power amplifier enabled (TX power config set to +5dBm output power). I’m assuming the ZBMINI actually does know the true state of the switch, but it either doesn’t pass that info on to HA or HA doesn’t show it in any way. The on-off indication in HA is based on the state of the relay. Fix TS0601_air_quality_sensor formaldehyd and voc units. https://github.com/Koenkk/zigbee2mqtt/issues/11033A fast response (the same as just after the pairing of the device). How to reproduce it (minimal and precise)

Fix formaldehyd/voc value incorrect for _TZE200_ryfmq5rl. https://github.com/Koenkk/zigbee2mqtt/issues/11033 I am considering putting some of these in to make my ceiling fans smart (just the light kit). My concern is that my circuit is the standard 15A and this zbmini is only rated for 10A. What if we plug some things into the outlet, down circuit from this device, and draw 12A (for example)? Are there concerns that this device might fail or… idk… catch fire, explode, etc? Sonoff ZBMini-L2, også kendt som ZBMINI Extreme, er den seneste udgave af Zigbee-smartkontakten uden nul-leder, som kan styres via deres app eWeLink, når den er tilsluttet en Zigbee-bro. Med sit kompakte design passer denne smartkontakt nemt i de mindste EU-type/86-type/120-type monteringskasser - dvs. også de danske!

Success!

It does have limitations you have to keep in mind. It will not work with inductive loads (like fans) and requires the connected device to use at least 3W power. It is rated as 6A 250V max. In my mind it seem it will be used mostly for lighting.

Revert unnecessary removal of old code that reads the position after sending stop command (Koenkk#4037) https://www.reddit.com/r/homeautomation/comments/skbvns/finally_a_sonoff_zb_mini_that_works_without/ Add TZE200_k6jhsr0q to TS0601_switch_4_gang. https://github.com/Koenkk/zigbee2mqtt/discussions/10071 Fix state in uppercase not working for KMPCIL_RES005. https://github.com/Koenkk/zigbee2mqtt.io/pull/1368 Add TS1002 modelID to _TZ3000_xwh1e22x fingerprint. https://github.com/Koenkk/zigbee-herdsman-converters/pull/4153Provedení modulu bez neutrálu sebou nese ale jeden problém. Takové zařízení nefunguje jako tzv. Zigbee router (tzn. nepřenáší povely kooordinátoru dál), ale pouze jako tzv. koncové zařízení (RFD). Což je u takto ne zcela standardně napájeného zařízení pochopitelné. Podle některých zdrojů se takové zařízení může (cituji) v Zigbee síti chovat někdy „škodlivě“, a může zvyšovat zátěž Zigbee koordinátora. A v konečném důsledku oslabuje „stabilitu Zigbee sítě“. A to je možná kámen úrazu, čtěte dál. Nový modul Sonoff ZBMINI-L2 Extreme vůbec nespolupracuje s Philips HUE Bridge

After you have wired the cable between ZBMINI Extreme and the device, you will want to connect an external switch to S1 and S2. Zigbee-teknologien er en standardiseret trådløs protokol inden for smart home og IoT, designet specielt til kommunikation mellem smarte hjemmeenheder. Zigbee-enheder har ikke en Wi-Fi-chip og tilslutter ikke direkte til en Wi-Fi-router, men kommunikerer i stedet med en Zigbee-gateway eller hub.SONOFF also have their own Zigbee USB dongle: the SONOFF Zigbee 3.0 USB Dongle Plus, but you can select Zigbee Dongle USB from any other brand such as the Conbee II from Dresden Electronic which we are using with a Raspberry Pi 4 in this review. Once you have a Zigbee USB dongle, you’ll then need to integrate it into your home automation framework. There are various Zigbee integrations for Home Assistant, but I would recommend either Zigbee Home Automation (ZHA) which is quite easy to install/set up from the Home Assistant GUI, or Zigbee2MQTT. Both have lots of users with plenty of Zigbee end devices supported.